KILZ 3® PREMIUM primer is a superior quality, fast drying, low odor, very low VOC, water-based primer-sealer-stainblocker. It has excellent adhesion and provides a mildew resistant coating making it ideal for use in moisture-prone areas. KILZ PREMIUM primer blocks most medium to heavy stains caused by water, tannin, ink, pencil, felt marker and grease. Its thicker high hiding formula hides surface imperfections and prepares the surface better for painting.

Use on interior and exterior surfaces including woodwork, drywall, plaster, paneling, masonry, brick, painted metal and properly prepared glossy surfaces. Works with oil and water-based paints.

Preparation, Application, & Clean-Up +

Surface Preparation*:

The following steps are recommended for product performance.

All surfaces must be clean, free of dust, chalk, oil, grease, wax, polish, mold and mildew, loose peeling paint, rust and all other foreign substances.
If washing is necessary, use a non-soapy detergent or a TSP substitute, rinse well and allow to dry.
Peeling or Checked Paint: Scrape off loose paint and sand to a smooth surface. Sanding or removal of paint containing lead is hazardous.*
†Glossy Surfaces: For maximum adhesion, scuff sand the surface thoroughly before priming.*
Mold or Mildew Covered Surfaces: Wash the area with a mildew remover, rinse with water and allow to dry before priming.
Masonry, Brick, Stucco and Plaster: KILZ 3® PREMIUM Primer may be used on clean, dry, aged masonry surfaces. New masonry must be allowed to cure (dry) at least 30 days before applying KILZ 3® PREMIUM Primer.
Fire Restoration: It is critical to clean damaged surfaces thoroughly before priming. Primer recommendations: KILZ® RESTORATION for water-based (interior); KILZ® ORIGINAL or KILZ® ORIGINAL EXTERIOR for oil-based.

Application:

Eye protection is recommended. For spray applications, a small amount of water (no more than 1/2 pint per gallon) may be added. Do not thin for stainblocking applications.
Only apply if surface, air and product temperatures are between 50°-90°F (10°-32°C). Stir thoroughly before and occasionally during use. Apply using a brush, roller or sprayer.
Brush – High quality Nylon/Polyester
Roller – High quality 3/8-1/2" nap on smooth surfaces or 1/2-3/4" nap on semi-rough or porous surfaces.
Airless spray – .017-.021 tip / 60 mesh filter
Prime the entire surface to ensure a uniform appearance of the topcoat.
Stainblocking: After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, a longer dry time is needed before topcoating.
Tinting: KILZ 3® PREMIUM Primer may be tinted with up to 2 ounces of universal colorant per gallon. Tinting to a lighter shade than the topcoat is recommended.
Coverage: 300-400 sq. ft. (27.87-37 m2) per gallon depending on application method and surface porosity.

Dry Time At 77°F (25°C), 50% RH:

Dries to the touch in 30 minutes.
Can be recoated or topcoated in one hour with latex or oil-based paint.
Application at lower temperatures, in high humidity or in poorly ventilated areas will affect dry time.

Clean Up & Disposal:

Clean equipment and paint spatters with warm, soapy water.
Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.
If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations. For recycling or disposal information contact your local household refuse collection service.

Warnings: +

†WARNING!: This product contains chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm.

USE ONLY WITH ADEQUIATE VENTILATION

WARRING! IRRITANT!

CAUTION IRRITANT Avoid contact with eyes. May cause eye, nose and throat irritation. Avoid breathing of dust, vapors or spray mist. Open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headache or dizziness or if air monitoring demonstrates vapor/ mist levels are above applicable limits, wear an appropriate, properly fitted respirator (NIOSH / MSHA TC -23C or equivalent) during and after application. Follow respirator manufacturer’s directions for respirator use. Close container after each use. Wash thoroughly after handling and before smoking or eating.

†WARNING!

If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

FIRST AID

If swallowed, do not induce vomiting. Get medical attention immediately. If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical attention immediately. In case of eye contact, flush eyes immediately with plenty of water for at least 15 minutes and get medical attention.

KEEP FROM FREEZING. If frozen, let thaw at room temperature.

KEEP OUT OF REACH OF CHILDREN

Specifications

Base	Water
Int/Ext	Int/Ext
Color	White
Coverage - Low	300 sq ft/gal
Mils Wet	5.3
Mils Dry	2.2
Coverage - High	400 sq ft/gal
Mils Wet	4
Mils Dry	1.6

Finish @ 85°	<10>
Min Application Temp	50°F (10°C)
Max Application Temp	90°F (32°C)
Viscosity	95 - 105 KU
Dry To Touch	30 min
Dry To Recoat	1 hour
Max Tint	2 oz
VOC	<5 g l>
Brush	Nylon / Poly

Roller - Smooth Surface	3/8 in. - 1/2 in. nap
Roller - Porous Surface	1/2 in. - 3/4 in. nap
Spray Tip	.017 in. - .021 in.
Spray Filter	60 mesh
Spray Pressure	2,500 - 3,000
Volume Solids	54.7% (+/-) 2%
Weight Solids	40.5% (+/-) 2%
Flashpoint	N/A

Similar Products

KILZ 3 Premium Interior & Exterior Primer, 1 qt.

{{title}}